How To Take A Glock Apart

Download Article

Download Article

If you own a Glock pistol, it is important that you know how to disassemble information technology to perform general maintenance. While at that place are many different types of Glock pistols, you can disassemble them all in much the same manner. Follow this guide to safely field strip your Glock in merely a few minutes.

1. one

   Indicate the pistol in a safe direction. Make sure that the pistol is pointed in a management where any accidental discharge cannot cause physical impairment to you or anyone else.^[1]

   • Keep your finger away from the trigger, and outside of the baby-sit. This volition assistance preclude adventitious firing.^[2]

2. two

   Release the mag. Printing the magazine release with your thumb and remove the magazine with your other hand.

   Advertisement

3. iii

   Open the slide. While continuing to indicate the gun in a safety management, pull the slide back and lock information technology open up with the slide end lever. You tin can push the lever up with your pollex while property the slide back with your other hand. This will hold the slide open.

4. four

   Cheque for remaining armament. Once the slide is open up, await into the chamber and ensure that no ammunition remains in the gun. Use your pinky finger to sweep for armament in the sleeping accommodation as well.^[3]

   • Check three times for remaining ammunition before proceeding to disassemble the gun.

Advert

1. ane

   Put on safety glasses. In that location are several components that are leap-loaded and tin cause serious eye damage. The glasses will also aid protect from solvents and lubricants getting in your eyes.

2. 2

   Close the slide. Pull the slide back to release the finish lever. The slide will close. Point the gun in a safe direction and pull the trigger to release the firing pin.^[iv]

3. 3

   Grip the gun. Hold the gun in one hand, with four fingers effectually the meridian of the slide, and the thumb holding the grip.

4. 4

   Pull back the slide. Using the four fingers on the elevation of the slide, pull it back about ane/tenth of an inch. If you pull information technology dorsum likewise far, you will demand to pull the slide all the way back and restart the process.

5. 5

   Pull down the slide lock. Using your other hand, pull down both sides of the slide lock lever. Push the slide frontward with your four fingers until it has separated from the receiver of the gun.

Advertizing

1. ane

   Remove the spring. Push the bound frontward slightly and lift it away from the barrel. The jump is under pressure, so be careful when removing it.

2. two

   Pull the barrel out of the slide. Concur the barrel past the extruding lugs. Lift the barrel while pushing frontward slightly. Raise and pull the butt out of the slide.^[5]

3. 3

   Clean the gun. Once the Glock has been disassembled, you lot can keep to clean the gun. You do not need to detach the Glock any further than this to properly make clean and maintain it.^[half-dozen]

4. 4

   Reassemble the gun. Once y'all are finished cleaning, y'all can reassemble the gun by reversing the above steps. You will not demand to hold the slide lock downwards when putting the slide back on the receiver.

Advertising

Add New Question

• Question

  What to do if wire comes completely out of braces before seeing a dentist?

  

  Jax Monroe

  Community Answer

  Do nothing. Just wait. Effort to get the dentist to schedule a coming together sooner than they offered by explaining what has happened.

Enquire a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Advert

• It is recommended that y'all wear safety spectacles, since there are spring loaded parts that could cause eye damage.

Cheers for submitting a tip for review!

Advertisement

• Make sure the pistol is always pointing away from yourself and anyone else.

• Never look downwardly the front of the gun barrel to cheque if bedchamber is unloaded.

• NEVER, during the disassembly, should your finger be on the trigger.

Advertising

Almost This Commodity

Commodity Summary X

To detach a Glock pistol, y'all'll need to safely unload it so remove the slide and barrel. Outset, you'll need to betoken the gun in a safe direction and release the magazine. Pull open and lock the slide so you can bank check the bedroom for any remaining ammunition. Side by side, y'all should shut the slide and fire one time in a safe management to release the firing pin. Afterwards, open the slide slightly and pull downwards on both sides of the slide lock. In one case the lock is in place, you can push the slide forward to separate it from the gun. You'll also demand to push the spring forwards out of the gun and pull out the barrel. When these parts of the gun are removed, you can clean your Glock before reassembling it. Remember to wear safety goggles when working with your gun in case of any accidents. For tips on how to put the slide back on when reassembling your gun, keep reading!

Did this summary assist you?

Thanks to all authors for creating a page that has been read 200,060 times.

Did this article help y'all?

Source: https://www.wikihow.com/Disassemble-a-Glock

Share this post